You can always call
with your Questions
(810) 987-3765
Primary tagline goes here!
What's New:
Time to Schedule
February 06, 2012
Now is the time to line up your project for 2012. Call Tod or Kathy today for a consultation:
810-987-3765
Recent Events:
December 16, 2011
After a very wet and challenging year of 2011, we are finishing up our final
jobs. Thank you to all our customers we were able to serve this year!
Looking forward to another great year in 2012.
(10% showers that day pictured turned to 4 hours of heavy
drizzle...great stamped patio was the result in the end though)
Frequently Asked Questions
Type in your Search Term
- What does it mean to "cure" concrete?
- Can it be too hot or too cold to place new concrete?
- What is air-entrained concrete?
- What are recommended mix proportions for good concrete ?
- Why does concrete crack?
- Why do concrete surfaces flake and spall?
- What is 3,000 pound concrete?
- How do you control the strength of concrete?
- How do you remove stains from concrete?
What does it mean to "cure" concrete?
- Curing is one of the most important steps in concrete construction, because proper curing greatly increases concrete strength and durability. Concrete hardens as a result of hydration: the chemical reaction between cement and water. However, hydration occurs only if water is available and if the concrete's temperature stays within a suitable range. During the curing period-from five to seven days after placement for conventional concrete-the concrete surface needs to be kept moist to permit the hydration process. new concrete can be wet with soaking hoses, sprinklers or covered with wet burlap, or can be coated with commercially available curing compounds, which seal in moisture.
Back to Top
Can it be too hot or too cold to place new concrete?
- Temperature extremes make it difficult to properly cure concrete. On hot days, too much water is lost by evaporation from newly placed concrete. If the temperature drops too close to freezing, hydration slows to nearly a standstill. Under these conditions, concrete ceases to gain strength and other desirable properties. In general, the temperature of new concrete should not be allowed to fall below 50 Fahrenheit (10 Celsius) during the curing period.
Back to Top
What is air-entrained concrete?
- Air-entrained concrete contains billions of microscopic air cells per cubic foot. These air pockets relieve internal pressure on the concrete by providing tiny chambers for water to expand into when it freezes. Air-entrained concrete is produced through the use of air-entraining Portland cement, or by the introduction of air-entraining agents, under careful engineering supervision as the concrete is mixed on the job. The amount of entrained air is usually between 4 percent and 7 percent of the volume of the concrete, but may be varied as required by special conditions..
Back to Top
What are recommended mix proportions for good concrete?
- Good concrete can be obtained by using a wide variety of mix
proportions if proper mix design procedures are used. A good
general rule to use is the rule of 6's:
• A minimum cement content of 6 bags per cubic yard of concrete,
• A maximum water content of 6 gallons per bag of cement,
• A curing period (keeping concrete moist) a minimum of 6 days, and
• An air content of 6 percent (if concrete will be subject to freezing and thawing).
Back to Top
Why does concrete crack?
- Concrete, like all other materials, will slightly change in volume when it dries out. In typical concrete this change amounts to about 500 millionths. Translated into dimensions-this is about 1/16 of an inch in 10 feet (.4 cm in 3 meters). The reason that contractors put joints in concrete pavements and floors is to allow the concrete to crack in a neat, straight line at the joint when the volume of the concrete changes due to shrinkage. Concrete will always crack, our hope is it is minimal and along the sawcuts that we place.
Back to Top
Why do concrete surfaces flake and spall?
- Concrete surfaces can flake or spall for one or more of the
following reasons:
• In areas of the country that are subjected to freezing and thawing the concrete should be air-entrained to resist flaking and scaling of the surface. If air-entrained concrete is not used, there will be subsequent damage to the surface.
• The water/cement ratio should be as low as possible to improve durability of the surface. Too much water in the mix will produce a weaker, less durable concrete that will contribute to early flaking and spalling of the surface.
• The finishing operations should not begin until the water sheen on the surface is gone and excess bleed water on the surface has had a chance to evaporate. If this excess water is worked into the concrete because the finishing operations are begun too soon, the concrete on the surface will have too high a water content and will be weaker and less durable.
Back to Top
What is 3,000 pound concrete?
- It is concrete that is strong enough to carry a compressive stress of 3,000 psi (20.7 MPa) at 28 days. Concrete may be specified at other strengths as well. Conventional concrete has strengths of 7,000 psi or less; concrete with strengths between 7,000 and 14,500 psi is considered high-strength concrete.
Back to Top
How do you control the strength of concrete?
- The easiest way to add strength is to add cement. The factor that most predominantly influences concrete strength is the ratio of water to cement in the cement paste that binds the aggregates together. The higher this ratio is, the weaker the concrete will be and vice versa. Every desirable physical property that you can measure will be adversely effected by adding more water.
Back to Top
How do you remove stains from concrete?
- Stains can be removed from concrete with dry or mechanical
methods, or by wet methods using chemical or water.
Common dry methods include sandblasting, flame cleaning and shot blasting, grinding, scabbing, planing and scouring. Steel-wire brushes should be used with care because they can leave metal particles on the surface that later may rust and stain the concrete.
Wet methods involve the application of water or specific chemicals according to the nature of the stain. The chemical treatment either dissolves the staining substance so it can be blotted up from the surface of the concrete or bleaches the staining substance so it will not show.
To remove blood stains, for example, wet the stains with water and cover them with a layer of sodium peroxide powder; let stand for a few minutes, rinse with water and scrub vigorously. Follow with the application of a 5 percent solution of vinegar to neutralize any remaining sodium peroxide.
Back to Top
